The contest that almost was!!!

[sparkie1263]

The wife setup one of our Christmas trees. Took this two shot pano with the 50mm lens. This was taken hand held with flash.
Frank

http://i305.photobucket.com/albums/nn219/sparkie1263/SmallTreePano.jpg

[jimr-pdx]

I might have entered something too.. like from my new Tam 18-250.
Hey, collages are nice, and easy, in Picasa 3!

http://lh5.ggpht.com/_t0ROcoSshLc/STipdnxOOGI/AAAAAAAABcM/BxF6xQ1CZU8/s800/MegaTam.jpg

[sparkie1263]

The tree is up.
Frank

http://i305.photobucket.com/albums/nn219/sparkie1263/28-200%20Lens/XmasTree.jpg

[Peekayoh]

Yipee! "Christmas is a comin', Christmas is..." that Coke ad.

[DonSchap]

I am actually still putting together my "Christmas shot" ... quite literally.

42538

42539

I suppose you all can guess what it is ... :) Yeah, a "WIP" (work in progress)!

Tomorrow's & Thursday's tasks:

Drill Press 7/8"-holes in PVC poles/stakes (for ease of setting in ground with removable solid-steel cross peg)
Epoxy stake connections (and let cure) in PVC poles (that should hold 'em)
Drill holes in top of PVC caps and insert and epoxy 3" long-1/2" thick carriage bolts
Drill the 4-corner angled-holes into upper wooden section
Epoxy washers top and bottom to penetrations to steel-reinforce connecting points in upper wooden section
"Rubber-coat" exposed steel connections to reduce wind-noise and protect from weather
Do basic construction for alignments and drilling of "connection points" in PVC poles.
Urethane all wooden surfaces for weather-protection
Paint PVC poles to color match "urethaned" wood
Insert connecting points in PVC poles ... and Epoxy to prevent loosening
Screw in connection hooks in wooden sections
Do final test assembly
Transport to final site for erection and evaluation of additional lighting (if necessary)
Photograph final layout and submit to DCRP thread (most important part of the effort :D )


The lumber yard left all this rough cedar wood outdoors and it was covered in ice, when I brought it in, this afternoon. I sure hope it all dries out enough to urethane it. :eek: Anyway, I probably missed some incidentals ... but, this short list should take care of most of what lies ahead.

And you thought you were busy for your "Christmas shot" ... :rolleyes:

BTW: The tree is up ... but, only half lit. Lost the end of a cord somewhere in there ... but, first things first, right?

[DonSchap]

Tomorrow's & Thursday's tasks:

Drill Press 7/8"-holes in PVC poles/stakes (for ease of setting in ground with removable solid-steel cross peg)

Forget that nonsense ... PVC shatters like glass if you drill it too big. 7/8" is just too big a bite out of 1-1/2" PVC! Time for a new approach to this issue.



Epoxy stake connections (and let cure) in PVC poles (that should hold 'em)


Newsflash: Epoxy does not bind with PVC! Once dry, makes a nice water-proof seal, but PVC just pulls apart. Need to use PVC Cement, which literally melts the PVC together ... and you'd need to hacksaw it apart. ;)



Drill holes in top of PVC caps and insert and epoxy 3" long-1/2" thick carriage bolts


This actually worked, but only because the Epoxy literally bonded the steel bolt like a flange through the hole. It's holding and I'm not complaining :o



Drill the 4-corner angled-holes into upper wooden section


This was rough to estimate and the holes need a little touch up.



- Epoxy washers top and bottom to penetrations to steel-reinforce connecting points in upper wooden section
- "Rubber-coat" exposed steel connections to reduce wind-noise and protect from weather
- Do basic construction for alignments and drilling of "connection points" in PVC poles.


Done!

Getting that roof section up from and out of the basement was a real strategic effort ... extraordinarily tight, being in excess of eight feet long and five feet wide, with about one-inch (or less) of clearance, held at an angle ... but hey, it's out in one piece ... and no gouges in the ceiling or the walls! Yes! :D (Honestly though ... I could not have cut it any closer. :eek: )

The remaining "To-Did" List



Urethane all wooden surfaces for weather-protection
Paint PVC poles to color match "urethaned" wood
Insert connecting points in PVC poles ... use "Lock-Tite" prevent loosening
Screw in connection hooks in wooden sections
Do final test assembly
Transport to final site for erection and evaluation of additional lighting (if necessary)
Photograph final layout and submit to DCRP thread (most important part of the effort :D )



I am beginning to think the PVC may not have the structural strength to support this thing, especially in this frosty weather ... and I'm reconsidering galvanized pipe and perhaps shortening the front by a foot in height (from 6' to 5'). Problem is that galvanized is about five times heavier than PVC and just murder to drill through ... and it may even be dangerous for children to work with, once I release the structure. Kind of puts a whole new face on the entire project. Problem stems from the intense winds that occur where this will be located. Even with extra cable tethers and auger stakes ... the current PVC just may not have the sheer durability to last the season. :(

2x4 studs have some merit, but wood rots after time ... and the structural support is not where I want that to occur. Sure, you could replace it, I suppose, but that kind of where this all started. The galvanized pipes seem so much cleaner ... easier to set (almost like tent poles) and will not suffer from the weather.

Tomorrow is another day! :eek:

[sparkie1263]

Don You can get galvanized pipe one size smaller and slide it inside the PVC that is how they do it with the railings down here.
Frank

[DonSchap]

Makes sense ... but, that certainly won't make it any lighter ... LOL ... although, at this point, is a serious consideration. I had actually considered "doubling up" (one inside the other) the PVC (for ease of drilling) ... but, it still lacks that cold resistance. I know, in my heart, it's probably going to "snap" with enough force applied ... so perhaps this would be the way to go ... :rolleyes: (<- looking thoughtful, as Andy likes to say).

Thanks for the suggestion, Frank. Good job!

[DonSchap]

Okay, Frank ... I did try a couple of things with your suggestion. First off ... it may be nice to know that 1-1/4" PVC or Galvanized will NOT fit inside of 1-1/2" PVC. The O.D. (outer diameter) of the 1-1/4" pipe is actually a tiny bit larger than the I.D. (inner diameter) and the 1-1/4" pipe is not going to slip in there as far as I can figure. I suppose I could split the PVC, but that kind of defeats the integrity aspect. :(

1-1/2" PVC and galvanized pipe does fit inside 2" PVC, though ... but, there is a significant gap remaining. For my use, that's probably okay, but this total scraps the previous 1-1/2" PVC poles I made and I am starting fresh ... along with the associated drilling, tomorrow. Arrgh ... the things I do for charity. LOL Some values never die ... but these "projects" are killin' me.

The stakes fit in the galvanized, too :) ... I just have to find a way to secure them. I suppose I could just leave them able to separate, as long as I use the tie-down augers in the set up. And yes, they are pretty heavy. :rolleyes:

The urethane coat of the wood is complete, except for some touch up on the edges. ... but, I lost a good part of the day to doing this "galvanized-upgrade." Oh, it had to happen, but it took two hours to finally get the proper pipe length cut. Everyone is cutting back on available in-store stock and I actually had to go to TWO separate stores to get four pieces of pipe! Strange days. Bought a "COBALT" bit and it easily bored through the pipe, so the holes are done, too. :D

I elected to eliminate the PVC sleeve idea (man, i have lots of tubing, now) and went with "Dutch Boy" outdoor acryllic paint, instead, roughly the same color as the wooden panels. Two coats and it is looking good.

Looks like it will be Saturday to finally get this put in, as the temperature should be a little warmer. We are currently at 14° F. Saturday looks like 38° F and raining. Hopefully, softer ground to get this placed. Then I can get MY "holiday shot."

How about the rest of you dudes? Let's see something festive! :D

[DonSchap]

Well, Saturday came and went ... and the thermometer is rising! It is supposely getting to 52°F, today, and it's raining! Yes! Perfect. (Who would have thought I would have wanted rain? Strange days, indeed.)

Today is the day .... that the Lord has made ... and this upcoming shot, only hours away, should be a testiment to that very thing. I'm ready to pound sand, as it were, and get this thing up and workin'. A place for the Savior. I suppose if Obama still needs a place to stay (since the "Blair House" is occupied), if it were good enough for the First Savior ... well, ... :D

With the help of some contractors, my son's Eagle Project put in the church's new walkway and handicap entry ramp, about two years ago.

42652

It seems we are basically providing the entire entry, this season! (Holiday Images, hopefully, to follow ;) )

The weather is doing things I have never seen before ... a truly serious warm spike, today, and then a serious plunge back to the arctic cold to follow. A real "wind-test", also ... gusts up to 40mph. A window of opportunity, basically timed perfectly for this effort. Things are moving in mysterious ways. :o Perhaps I may get a better shot if I just wait for the REAL weather to blow in ... :rolleyes: I won't be waiting long, that's for sure.

[DonSchap]

Well, the wind is a blowing a gale ... here in Chicagoland.

But, it's up and done! Wind resistance built right in ... and lil' Jesus does not wind up like the "Grey Gale."

The entry ...


42661


the obligatory second angle ... providing legitimacy ;)


42662


:D Merry Christmas and the happiest of holidays to one and all! :D

EDIT: The obligatory "night shot", from across the street, with its provided illumination.
@ 50mm


42683


@200mm w/ ISO 3200


42682

[sparkie1263]

Nice job Don. I think it should hold up. The snow should not build up on top so weight should not be an issue.

Frank

[DonSchap]

Thanks, Frank. Well, it's not the Taj Mahal ... but, that took more than four days, as I recall ... more like 17 years with 20,000 guys working on it DAILY! LOL And that was just for a dead woman! Anyway, with the guy-wires, it's a much more "stable" place for a young Savior to hang out for a few ... just to get started.

Do you think it needs some hay and other items to give it that ... Party Animal look? They were talking about adding

an ox ...

42678

and some donkey ...

42679

in the future iterations.

[DonSchap]

Anyway ... trying to get the dog to cooperate can be, well, trying! It was hard to get him to understand that I wanted him there ... to sit ... look at the camera ... be patient ... you know, the standard drill you cannot get human beings to do. He can be so intolerant and moody about these things. I also believe the sub-zero weather is playing hell with his attitude, too.

42871
EXIF: SONY A700 w/ CZ 135mm f/1.8
@ f/1.8 - 1/60 sec - ISO-100 - Manual Mode - Spot Meter - Manual Focus - Pop-up flash -> deflected for ceiling bounce

Anyway, here is that f/1.8 bokeh, using the CZ 135mm. He was about five feet from me (no crop), DOF is tight ... around his muzzle and eyes, but you can see the powerful effect on the Christmas tree behind him, about eight feet.

Here's the second angle ... only the DOF is on the eyes!

Possessed Holiday Pup!

42875

"You must look into my eyes, human ... do not resist ... and give up the treats!"